Chemical bond characteristics and infrared reflectivity spectrum of a novel microwave dielectric ceramic CaIn2O4 with near-zero τf

Orthorhombic-structured CaIn₂O₄ ceramics with a space group Pca2₁ were synthesized via a solid-state reaction method. A high relative density (95.6 %) and excellent microwave dielectric properties (ε_r ～11.28, Qf = 74,200 GHz, τ_f ～ ?4.6 ppm/°C) were obtained when the ceramics were sintered at 1375 °C for 6 h. The dielectric properties were investigated on the basis of the Phillips–Van Vechten–Levine chemical bond theory. Results indicated that the dielectric properties were mainly determined by the InO bonds in the CaIn₂O₄ ceramics. These bonds contributed more (74.65 %) to the dielectric constant than the CaO bonds (25.35 %). Furthermore, the intrinsic dielectric properties of the CaIn₂O₄ ceramics were investigated via infrared reflectivity spectroscopy. The extrapolated microwave dielectric properties were ε_r ～10.12 and Qf = 112,200 GHz. Results indicated that ion polarization is the main contributor to the dielectric constant in microwave frequency ranges.     

Toward a better understanding of multifunctional cement-based materials: The impact of graphite nanoplatelets (GNPs)

The impact of graphite nanoplatelets (GNPs) on the physical and mechanical properties of cementitious nanocomposites was investigated. A market-available premixed mortar was modified with 0.01% by weight of cement of commercial GNPs characterized by two distinctively different aspect ratios.The rheological behavior of the GNP-modified fresh admixtures was thoroughly evaluated. Hardened cementitious nanocomposites were investigated in terms of density, microstructure (Scanning Electron Microscopy, SEM and micro–Computed Tomography, μ-CT), mechanical properties (three-point bending and compression tests), and physical properties (electrochemical impedance spectroscopy, EIS and thermal conductivity measurements). At 28 days, all GNP-modified mortars showed about 12% increased density. Mortars reinforced with high aspect ratio GNPs exhibited the highest compressive and flexural strength: about 14% and 4% improvements compared to control sample, respectively. Conversely, low aspect ratio GNPs led to cementitious nanocomposites characterized by 36% decreased electrical resistivity combined with 60% increased thermal conductivity with respect to the control sample.     

Thermal and dynamic mechanical behavior of epoxy composites reinforced with post-consumed yerba mate

Yerba mate (YM) is widely consumed in Latin American countries, and its residues can be used as bio-resources such as reinforced in epoxy composites. The present work aims to produce epoxy resin composites and evaluate the influence of post-consumed YM as reinforcement. The concentrations of YM used were 5, 10, and 20% (wt/wt). Chemical, thermal, morphological, and dynamic mechanical behaviors were explored. The YM incorporation did not influence chemically on the epoxy structure and a pull-out phenomenon was observed as YM content increased. The YM at lower concentrations (5 and 10%) led to higher values of activation energies calculated from model-free isoconversional methods. On the other hand, the composite e/YM 20 wt% improved all dynamic-mechanical properties. YM proved to be a suitable and cheap reinforcement for epoxy resin.     

Development of a difunctional oxirane and multifunctional acrylate interpenetrating polymer network composite system with antimicrobial properties

This research continued the development of a difunctional Oxirane and multifunctional Acrylate interpenetrating polymer network composite System (OASys) with antimicrobial properties. The effects of 4-Isopropyl-4′-methyldiphenyliodonium tetrakis (pentafluorophenyl) borate (Borate), hexamethylene diamine (HMDA) and N,N-dimethyl p-toluidine (DMPT) on OASys (Epalloy 5001:dipentaerythritol hexaacrylate) composite hardness, contact angle, monomer-to-polymer degree of conversion (DoC), mechanical properties, polymerization shrinkage, shrinkage stress, and antimicrobial properties were determined. Bis-GMA:TEGDMA composites were used as the control. OASys composites with 9 wt% Borate and 0.5 wt% DMPT or 1.5 wt% HMDA had comparable hardness, DoC's and polymerization shrinkages to controls, but had lower contact angles and mechanical properties. Additionally, OASys composites with 1.5 wt% HMDA had significantly less polymerization stress than controls and demonstrated significant antibacterial activity against Streptococcus mutans and Lactobacillus casei out to 3 months. With lower shrinkage stress and long-term antimicrobial activity, OASys composites look promising for increasing the clinical lifetime of dental composites, but improvements in mechanical properties are needed.     

Wear and thermal behavior of basalt fiber reinforced rice husk/polyvinyl chloride composites

Plant fiber reinforced polymer composites (PFRPs) in practical application are often subjected to both complex friction and variable temperature environments. The present work explores the possibility of reinforcing rice husk/polyvinyl chloride (RH/PVC) composites with basalt fibers (BF) for developing a new wear resistant material with improved thermal stability. The results showed that the structural strength and wear resistance of the composites increased at first and then decreased with an increasing ratio of BF/RH, the highest value occurred at a BF/RH ratio of 8/42. The thermal stability of composites had a positive relationship with BF/RH ratio. The composites added with BF all possessed improved performance in comparison with unadded composites. Hence, the findings of this article proposed some new perspectives on improving the wear resistance and thermal stability of PFRPs that would broaden their practical application.     

How the biaxially stretching mode influence dielectric and energy storage properties of polypropylene films

The most important polymer film used in commercial capacitors is biaxially oriented polypropylene (BOPP), which could be produced by sequentially or simultaneously biaxial orientation after the melt-extrusion. In order to disclose the influence of the stretching technique on the properties of films, the BOPP films with varied thickness were fabricated by sequential and simultaneous orientation, respectively. Compared to the sequentially biaxially stretched films, the crystal grains in the simultaneously biaxially stretched films are more isotropically dispersed. As temperature increases, all the BOPP films exhibit similar dielectric constant, and the simultaneous films have much lower dielectric loss thanks to the finer blended crystalline and amorphous phases. When the film thickness is smaller than 5 μm, the breakdown field strength, energy density and discharging time of the simultaneous films can be increased by at least 10% comparing to the sequential ones, which is very important for reducing the volume of the film capacitors. All the results suggest the simultaneously biaxial orientation mode shows significant advantages in producing thin BOPP films with better mechanical and electrical properties.     

Influence of the stoichiometry,microstructure, and metallization method on the dielectric properties of 0.94 Na0.5Bi0.5TiO3-0.06 BaTiO3

The morphotropic composition of the lead-free solid solution between Na_0.5Bi_0.5TiO₃ and BaTiO₃ (0.94 Na_0.5Bi_0.5TiO₃-0.06 BaTiO₃ or NBT-6BT) is of particular interest for the next generation of high-temperature capacitors but remains plagued by the diversity of dielectric properties reported in the literature. In order to explain the apparent inconsistencies among the reported dielectric properties of NBT-6BT, we examine the influence of stoichiometry, phase separation, and metallization method. We show that the nominal stoichiometry has a crucial effect, since increasing the nominal Na/Bi ratio increases conductivity and dielectric losses (tan δ). It also increases the real part of the permittivity (ε’) and the frequency dispersion of both ε’ and tan δ, thereby altering the shape of the evolution with temperature of the dielectric properties. Moreover it increases the depolarization temperature (T_d) and decreases the temperature of maximum permittivity (T_m). Phase separation also occurs during the synthesis of NBT-6BT as Na evaporation leads to the formation of secondary Ba-containing phases. We report that these phases can have a positive impact on the dielectric properties: a moderate volume fraction (2.5 to 3.0%) and average grain surface (0.9 to 3.0 µm²) of these secondary Ba-containing phases increase the relative permittivity, decrease the dielectric losses, and increase the insulation resistance. We also show that the metallization method impacts the dielectric properties and therefore may contribute to the differences between various reports. The dielectric properties of NBT-6BT samples are measured during successive heating/cooling cycles and reveal that the permittivity value is lower during the first heating when silver paste, even cured, is used. These three components contribute to explaining the diversity of the reported dielectric properties of NBT-6BT.     

辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响

研究辊速差对连铸连轧7075铝板显微组织、织构及力学性能的影响。采用3种不同上辊/下辊转速比(ω/ω0,ω为上辊转速,ω0为下辊转速)1:1、1:1.2及1:1.4进行多次试验。结果显示,在最大辊速差条件下(ω/ω0=1:1.4),7075铝板在轧制方向的屈服强度和极限抗拉强度分别提高41.5%和21.9%。此外,当辊速比ω/ω0为1:1.4时,成品轧制板的平均晶粒尺寸减小36%,横剖面平均硬度增加约9.2%。织构研究结果显示,辊速差越大,成品各向同性及硬度越大。然而,采用不同辊速度的连铸连轧会导致变形板伸长率降低约6%。     

Effect of Bimodal Grain Size Distribution on the Strain Hardening Behavior of a Medium-Entropy Alloy

The evolution of strain hardening behavior of the Fe_(50)(CoCrMnNi)_(50) medium-entropy alloy as a function of the fraction of recrystallized microstructure and the grain size was studied using the Hollomon and Ludwigson equations.The specimens under study were partially recrystallized,fully recrystallized with ultrafine-grained microstructure,and fully recrystallized with coarse grains.The yield strength decreases steadily as the fraction of recry stallized micro structure and grain size increases due to the recovery process and the Hall-Petch effect.Interestingly,the bimodal grain distribution was found to have a significant impact on strain hardening during plastic deformation.For instance,the highest ultimate tensile strength was exhibited by a 0.97 μm specimen,which was observed to contain a bimodal grain distribution.Furthermore,using the Ludwigson equation,the effect of the bimodal grain distribution was established from the behavior of K_2 and n1 curves.These curves tend to show very high values in the specimens with a bimodal grain distribution compared to those that show a homogenous grain distribution.Additionally,the bimodal grain distribution contributes to the extensive L(u|")ders strain observed in the 0.97 μm specimen,which induces a significant deviation of the Hollomon equation at lower strains.